Whether you are a DIY enthusiast or an ordinary person aspiring to help around the house, everyone should know their way around a drill. A drill is a reliable tool used for multiple purposes, from drilling a hole in the wall to extracting and digging a nail.
Although handling such a power tool at first can be pretty challenging, we are here as your knight in shining armor! Drills are of two types, corded and cordless. Initially, learn all there is to know about a power drill, from its parts to its functions.
Moreover, when it comes to utilizing it, Boat Diaries has you covered. It has additional attachments such as a screwdriver at the front to do the work. Furthermore, a drill comes in a wide range of drill bit sizes and types.
Methods to work your way around the drill!
There is no need to be afraid of the scary power tool. You can quickly work your way around the drilling machine by taming it. We have listed some effective ways you can use to work with a drill machine. So waste no more time on your DIY crafts or construction projects; get started now!
1. Setup the drill
A cordless drilling machine is very easy to operate. For starters, check whether the drill’s battery is charged or not. The red light shows a low battery, whereas the green light indicates a charged battery. A drill moves in both directions, clockwise and anticlockwise. A button functions near the drill’s trigger, which controls the drill’s direction.
On the head indicator of the drilling machine, you can control the speed of the power tool. Most machines have two rates, low speed, and high speed. Moreover, add the drill bit to the head of the device that suits your handyman projects. Now adjust the point where you want to drill and set higher torque with lower speed.
The clutch at the front of the head helps adjust the machine’s torque. Torque ensures the rotating speed of the drill bit. Voila! Familiarize yourself with the primary setting of the drill, and you are good to go. Moreover, a higher voltage also adds to the functionality of the drill.
2. Drill into any material
Ready, set, and drill! Now you can drill into any fabric with just a basic guideline. Initially, hold the drill with one hand on its handle and the other on top of the drill. Position the drilling machine at a 90 degrees angle with the desired material. Apply steady pressure on the drill, and in case you want to stop, press the reverse button.
Use a little drill bit to make a pilot hole and afterward drill with a more significant bit for better results. However, another tip for drilling into dense material is checking the size of the screw with a drill bit. While dealing with thicker material, mark a pilot hole for more accessible functionality.
3. Use multiple drill bits
The ease of drilling depends on the drill bit you are using. First, loosen the chuck of the drilling machine, and remove the drill bit. Hold the chuck firmly and turn it in the right direction, which will help loosen the prongs that hold the bit. Afterward, check the suitable drill bit for the desired project.
These bits are available in all tool shops in multiple designs and sizes. You can select from the many options such as twist, masonry, spur point, and spade bits. At last, plug in your required bit and tighten the clutch until all the three prongs settle evenly around the shank.
Common drilling mistakes to avoid
While drilling holes, some common mistakes can cause trouble for beginners. The most common of these errors is not using the right bit. Each bit is designed for a specific surface, whether concrete, wood, or metal. Using the wrong bit can ruin the surface, bit, and even the drill machine.
Using the wrong speed settings is also a common mistake that many people make. In order to ensure that an accurate job can be achieved, specific drills are designed to be worked at precise speeds and pressures. As a result, a handheld drill can be set so that it goes too fast for the size of the drill bit that it can blunt or break if it is set to go too fast.
Some final thoughts!
Drills sound intimidating because of their heavy power duty. You can also use drilling machines for all your projects once you go through the methods. Calling a professional handyperson for ordinary tasks is very costly, with an estimate of 50$ – 350$ per day in the UK.
Hence it’s always convenient to acquire basic skills regarding tools—no need to spend such a hefty amount on professionals for minor tasks that you can perform better. Learn the basic functioning of working a drilling machine on BoatDiaries.com and get to work!